PARTNER® Advanced Communications System Processor Module
3 modular loop start line ports with Caller ID capability
8 modular enhanced tip/ring (ETR) extension ports
The first two provide power failure transfer to the first two lines
2 slots for PCMCIA cards
2 touch-tone receivers
1 music source port (RCA type)
1 modular loudspeaker paging port
1 modular SMDR port
1 modular jack to connect to an optional contact closure device

308EC Module
3 modular loop start line ports with Caller ID capability
8 modular ETR extension ports
2 touch-tone receivers

362EC Module
3 analog CO lines
6 ETR only station ports
2 full function ETR station ports with full tip/ring functionality

400EC Module
4 modular loop start line ports with Caller ID capability
2 touch-tone receivers

012E Module
12 ETR station ports
No power-failure transfer capability (no CO lines on 012E module)
Supports 48 stations
Supports full T/R capability along with ETR

1600 DSL Module
SDSL capability
Provide router functions, up to 16 voice channels

PARTNER Advanced Communication System R4.0 will only support one 1600 DSL module and that module can only be used in slot 1 of a 5-slot carrier or in the expansion slot of a 2-slot carrier.

No power failure transfer capability

Extension Jack
Maximum 2 devices per extension jack can be a system phone plus a standard device or 2 standard devices total Ringer Equivalency Number (REN) on jack not to exceed 2.0
No more than 1 system phone per jack

Dimensions and Weights (Approx.)

Processor module
11"(D) x 17"(H) 1.5"(W) or 27.9 x 43.2 x 3.8 cm
4.5 lbs or 2.0 kgs

308EC module
11"(D) x 17"(H) 1.5"(W) or 27.9 x 43.2 x 3.8 cm
4.0 lbs or 1.8 kgs

400EC module
11"(D) x 17"(H) 1.5"(W) or 27.9 x 43.2 x 3.8 cm
4.0 lbs or 1.8 kgs

1600 DSL module
11"(D) x 17"(H) 1.5"(W) or 27.9 x 43.2 x 3.8 cm
4.0 lbs or 1.8 kgs

2-slot carrier
2"(D) x 9.75"(H) 5.5"(W) or 5.1 x 24.8 x 14 cm
1.0 lbs or .46 kgs

5-slot carrier
12"(D) x 19"(H) 11"(W) or 30.5 x 27.9 x 14 cm
5.5 lbs or 2.5 kgs

Switch Fabric
Full digital, non-blocking

Electrical Specifications

45 watts (154 BTUs/hr.) per PARTNER® Advanced Communications System processor module during normal power consumption

85 watts (290 BTUs/hr.) per PARTNER® Advanced Communications System processor module during maximum power consumption

10 watts (35 BTUs/hr.) per 400 module, normal and maximum power consumption

42 watts (147 BTUs/hr.) per 308 module, normal and maximum power consumption

16 watts (56 BTUs/hr.) per 1600 DSL module, normal and maximum power consumption
45 days to 6 months memory backup with 2 AAA-size standard alkaline batteries (IEC LR03)

Processor Module Specifications

68306 16 Mhz processor
256 Kbyte RAM
512 Kbyte Flash ROM
Custom VLSI DSP ASIC—16-bit, 52 MHz

Extension Jack Specifications
Ringing voltage: +5 VDC, -140 VDC peak to peak; trapezoidal wave shaping
35 to 38 Volt talk battery
Ringing frequency: 20 Hz

Page Jack Specifications
Draws current on inner wire pair
Provides paging contact closure on outer wire pair
600 Ohm impedance

Music on Hold Specifications
Accepts 2 Volts at 50 Kohms maximum input
0-18 dB attenuation

Contact Closure Adjunct Specifications
Operates up to 150 feet (45.72 meters) from control unit using 24 gauge solid conductor wire if 2 contact closure devices are used; up to 800 feet (243.84 meters) from control unit using 24 gauge solid conductor wire if 1 contact closure device is used
Install the contact closure adjunct in the same building as the control unit; cannot be installed out-of-doors
Has 3 terminals per contact closure, providing a normally open and normally closed function for each contact closure
Maximum contact voltages and current
30 VAC, 1 Amp
50 VDC, 1 Amp

SMDR Output Format Specifications
1200 baud, 8 data bits, XON/XOFF protocol, Line feeds, No parity, 2 stop bits, Carriage return

Environmental Requirements: Control Unit
Mount on a wall at least 2 feet (0.6 meters) from the floor (wall mounting required)
Locate within 5 feet (1.5 meters) of the network interface jacks and a properly grounded electrical outlet not controlled by a switch, using supplied 7-foot (2.1 meter) cords
Operating temperature of room: 32 to +104 F (0 to +40 C), not in direct sunlight
Humidity 15% to 90% non-condensing
For proper ventilation and easy replacement of modules, provide the following maximum clearance around the control units:
5-slot carrier: 1 foot (0.3 meter) clearance at the top and sides, and 2 feet (0.6 meter) clearance at the front and bottom
2-slot carrier or stand-alone PARTNER® Advanced Communications System processor module: 1 foot (0.3 meter) clearance at the front, top, and right side, and 2 feet (0.6 meter) clearance at the bottom and left side
Locate in an area free of excess moisture, corrosive gases, dust, and chemicals

Electrical Requirements: Control Unit
U.S. and Canada: 90-130 VAC, 50-60 Hz, 3-prong outlet separate ground, separately fused at 15 Amps
Other countries: 90-264 VAC (220 VAC fused at 10 Amps)
Grounding to comply with Underwriters Laboratories (UL) 1459

Requirements for Out-of-Building Installations
Installation of a telephone or other standard (tip/ring) device in another building requires the following In-Range-Out-of-Building (IROB) protectors to protect the control unit and device from electrical surges:
System phone: 2 IROB protectors
Standard phone: 1 IROB protector plus 1 carbon block protector
Installation of a contact closure adjunct controlled device outside the building requires a surge protector to protect the control unit from electrical surges.

Wiring
System phones: At least 2-pair (4-wire) star ("home run" not "loop") Other standard telecommunications equipment: 1-pair (2 wire) mounting cords Bridging adapter: 267F2 Range: 1000 feet (305 meters) for system phones; 3,000 feet (915 meters) for standard devices

Safety Requirements
U.S.: Meets UL 1459 Issue 2
U.S.
FCC Part 68 approval
FCC registration number (U.S.) See the label on the side of the control unit
PCC Part 15 approval
Class A: 5-slot configuration; 2-slot configuration with PARTNER® Messaging
Class B: PARTNER® Advanced Communications System stand-alone configuration; 2-slot configuration with 308EC, 400EC, and PARTNER® Advanced Communications System processor modules
REN (outside line jack): 0.9A per line jack
Jack type: RJ11C
Loop start lines